NEW PRODUCTS

New Products

939-2327

Pneumatic Operation Dent Puller

• Contents:---
  1pc Pneumatic Small Dent Damage Puller,
  10pcs Glue pads.
  1pc Extension Adapter.
  φ11.2mm x L25.4cm x 2pcs Hot Glue Sticks (just for body repair).

• Repair the small damage on the vehicle body.
• Operate more easily with pneumatic function.
• Safety devise on pressure control and flow control valves.
• With 10pcs glue pads and 1pc extension adapter.
• Stainless steel with PVC cover protection for non scratch and reliable usage.
• Air Inlet: 1/4”
• Operating pressure: 3 ~ 10Bar (0.3mMPa) (40~145psi).

• Operation Steps:
  Step 1: Choose the suitable tab, and put some hot glue on tab by hot glue gun.
  Step 2: Use heat gun to blow the hot glue of the tab to soften the hot glue.
  Step 3: Stick the tab to the small dent of the car, and use the heat gun to blow again to fix
               the tab and the small dent.
  Step 4: Wait for 5 seconds to cool the hot glue, and try to pull the tab by hand to check
               the tab and the small dent are stuck.
  Step 5: Connect the pneumatic small dent puller damage to the air compressor.
  Step 6: Adjust the pressure control valve of the puller. Then, hook the connective hook of
               the puller with the tab, and make sure They Are Hooked.
  Step 7: Adjust the two adjustable screws to make sure the height of the connective hook
               is suitable.
  Step 8: Press the trigger of the puller until the dent is recovered.
  Step 9: If it Is Necessary, rotate the puller to different angles and repeat the step 8 to
               make sure the whole dent is recovered.
  Step 10: Separate the puller and the tab, and then use the heat gun to soften the tab until
                the tab can be removed.
  Step 11: Use the heat gun to blow the glue on the dent place, and use the plastic scraper
                to scrape the Remaining glue. And the dent recovery is finished.

• Contents:---
  1pc Pneumatic Small Dent Damage Puller,
  10pcs Glue pads.
  1pc Extension Adapter.
  φ11.2mm x L25.4cm x 2pcs Hot Glue Sticks (just for body repair).

• Repair the small damage on the vehicle body.
• Operate more easily with pneumatic function.
• Safety devise on pressure control and flow control valves.
• With 10pcs glue pads and 1pc extension adapter.
• Stainless steel with PVC cover protection for non scratch and reliable usage.
• Air Inlet: 1/4”
• Operating pressure: 3 ~ 10Bar (0.3mMPa) (40~145psi).

• Operation Steps:
  Step 1: Choose the suitable tab, and put some hot glue on tab by hot glue gun.
  Step 2: Use heat gun to blow the hot glue of the tab to soften the hot glue.
  Step 3: Stick the tab to the small dent of the car, and use the heat gun to blow again to fix
               the tab and the small dent.
  Step 4: Wait for 5 seconds to cool the hot glue, and try to pull the tab by hand to check
               the tab and the small dent are stuck.
  Step 5: Connect the pneumatic small dent puller damage to the air compressor.
  Step 6: Adjust the pressure control valve of the puller. Then, hook the connective hook of
               the puller with the tab, and make sure They Are Hooked.
  Step 7: Adjust the two adjustable screws to make sure the height of the connective hook
               is suitable.
  Step 8: Press the trigger of the puller until the dent is recovered.
  Step 9: If it Is Necessary, rotate the puller to different angles and repeat the step 8 to
               make sure the whole dent is recovered.
  Step 10: Separate the puller and the tab, and then use the heat gun to soften the tab until
                the tab can be removed.
  Step 11: Use the heat gun to blow the glue on the dent place, and use the plastic scraper
                to scrape the Remaining glue. And the dent recovery is finished.

back to list